A New Mirror Out Of An Old Antique Door

This post may contain affiliate links, meaning I get a commission if you decide to purchase through my links, at no additional cost to you. As an Amazon Associate, I earn a few pennies from qualifying purchases. 

Hubby said this is one of his favorite projects that we've done!  I don't know if I agree, because I've loved soooo many of them! But this one is VERY cool!!

Antique Door to Mirror

We found these doors up in the attic of one of the properties we owned.  When I saw them, I knew they were coming home with me!

Antique Door

I wanted some sort of mirror in the mudroom/laundry room.  I just wasn't sure how or what would work there... then I thought of those doors!!  What if.....

I cut out the panels and replaced them with mirror???

cutting panels out of antique door

An hour or so later, with a hammer, spatula, screwdriver, multi-tool, sweat and grit... I got those panels out! It was a job!  But this is going to look so cool! I just love the character of old doors.

Next up... paint!  I did a bunch of research on how to create an 'old distressed multi layered paint look'... There are sooo many techniques to choose from.  I did a couple of different ones.  I tried the candle wax technique.

candle wax distressing technique

Basically, you rub candle wax on all the areas you want distressed.  Then paint over all of it. The paint doesn't adhere as well to the waxed areas.  Next, scrape those areas to reveal the wood beneath.

candle wax distressing technique

Okay... now, we're getting somewhere...

Let's try the other method... I used Johnson's Paste wax.  I globbed it on, and painted with a different color, more of a light minty green.  These are all old paints that I had on hand. 👍

Johnson's Past Wax distressing technique

The paste wax, in my humble opinion, worked better.  It seemed to scrape easier and gave the look I wanted.  Sometimes, I would just leave the scrapings and paint over them again...

You just gotta play with it a bit.  You really can't mess it up.

Distressing an antique door

So this is where I left it at.  I added more paste wax, more paint, more scrapping, more paint, more scrapping, and a little sanding...  you get the picture.  You just keep going until you get the look you like. 😊

I do have to admit, it was a little hard to stop... I kept questioning myself... Should I do one more? Is this good? Less is more, right? I finally just had to stop and be done! I'm glad I did! I love it!

Next up, let's find some mirror.

That was more of a challenge than I thought it would be.  Mostly because of the size of the large cut out.  First, I tried a glass/mirror shop in town.  They wanted $80 for both!! What??? No way was I going to pay that amount! 😝

Then I hit up Lowes, they do cut mirror, but not the size I needed... Ugh! What to do??

Hubby suggested a thrift store!  Yes! We have a Rescue Mission close by and they carry a lot of furniture and things...

Yureka!! Success!! I bought these two for $10 each!! Not perfect, but I don't need perfect!

Mirrors from rescue mission

We took them out of their frames, measured and figured out how to cut mirrors!

Measuring the mirror for cutting

I picked up this handy little glass cutter at Lowes.  This is the one Amazon.  It doesn't have great reviews, but it's the same one they had at Lowes.  There is a learning curve with it. Our first cut was not as successful as our next few.

Glass cutting tool

You need to hold it straight up, use a good amount of pressure and go slow.  We ended up scoring the glass more than once.  By the time we were done with the last cut, hubby had it down!

Scored Mirror ready to break on line

In the above photo you can see the scored line. We set our straight edge underneath that line for leverage.  Then hubby hit the glass with both hands.  Boom!

Cut mirror

Ahhh nice straight cut!  Here's a look at our first cut... it was a pain and a mess to break off all the pieces...

mirror cutting goes wrong

We figured, we didn't score it well enough and that's why some of it didn't break on the score line.  It's fine, that jagged edge doesn't show at all!

So, how was I going to get this mirror to stay in?? Well, after we put the mirrors in, I just laid the panels back into place over the mirrors and used liquid nails to seal it.  I used a bunch of books and paint cans on top to hold it all down.  I think it's good! This was after it was all dry.

Glued mirror in with panels

Then we needed to find some way to hang this beast on the wall!!!  This is one heavy mirror!  We looked at Lowes for a metal cleat.  But, I am way too cheap to pay for $9 for a 5 inch metal cleat, especially when Hubby was thinking we needed 2 of them. 😣

But Hubby always comes through!!! He's a genius! He found some metal thingamabobs in the garage and MADE a cleat for this door!! He's the best!! ❤️

Hubby's DIY Metal Cleat

He measured and mounted this bad boy on the wall! It is PERFECT!! ❤️❤️❤️

New mirror out of an antique door

I am in LOVE with this! I put the hold hardware back on.... 💕swoooonnn...💕

Oh! and we added two extra screws here... inside the door handle holes.  Just to keep it from sliding or anything... Just look at that trim piece... gorgeous! Can you see the screw where the door knob goes?  These doors didn't have the crystal door handle, but you can bet I'm on the hunt for one!

 Antique door trim

And you don't need to worry... the washer door opens and hits smack dab at the wood center of the mirror! Yay!!
A New Mirror Out Of An Old Antique Door

It's the perfect place to 'check yourself' before you leave the house. I am sooo happy with this project.  Hubby might be right... It might be one of my favorite projects! ❤️

Blessings!
A New Mirror Out Of An Old Antique Door


1 comment

  1. Hi there! I'm at work surfing around your blog from my new iphone!
    Just wanted to say I love reading your blog and look forward to all your posts!
    Keep up the great work!

    ReplyDelete